Fixing Door Handles On A Hummer H3

If the door handle of your 2006 Hummer H3 is damaged, worn out, or broken, you can easily replace it yourself. You will need a deep well 10mm socket (or standard size 10mm socket with an extension) and a flathead screwdriver. First, open the door and locate the round black cover near the door handle. Using the flathead screwdriver, pry off the rubber/plastic cover. Then, using the 10mm socket, remove the bolt carefully so that it doesn't fall inside the door panel. Next, pull slightly on the door handle as if you were opening the door, allowing the end cap of the door handle to move freely away. To remove the remaining handle assembly, pull and hit the hinge end of the handle toward the rear of the vehicle while tugging slightly. This will release two small plastic nubs holding the handle in place. To install a new handle, simply follow these steps in reverse. You can find replacement door handles for the 2006 Hummer H3 online or at auto parts stores.

Removing the door handle

To remove the door handle of a 2006 Hummer H3, you will need a deep well 10mm socket (or a standard 10mm socket with an extension) and a flathead screwdriver.

First, open the door and locate the round black cover near the door handle. This cover is about the size of half a dollar and is made of rubber or plastic. Using the flathead screwdriver, pry off this cover. Underneath, you will see a bolt. Using the 10mm socket, carefully remove this bolt, being careful not to let it fall inside the door panel.

Once the bolt is removed, pull slightly on the door handle as if you were opening the door. This will allow the end cap of the door handle to move freely away from the door. Now, to remove the remaining handle assembly, pull slightly on the handle and, with the base of your other palm, hit the hinge end of the handle (opposite of the end cap) toward the rear of the vehicle while tugging slightly. This action will release two small plastic nubs that hold the handle in place, and the remaining handle will come free. You may need to hit it a few times.

Please note that one of the small tabs on the hinge end of the handle may break off. However, this does not seem to affect the integrity of the handle.

Locating the round black cover

To locate the round black cover, first, open the door of your Hummer H3. The round black cover is located near the door handle and is about the size of half a dollar. Using a flathead screwdriver, you can pry off this rubber/plastic cover. Be careful not to scratch the surrounding area of your car door. Once the cover is off, you will see a bolt that needs to be removed with a 10mm socket. Again, be cautious when removing the bolt to avoid it falling inside the door panel.

Removing the bolt

To remove the bolt from the door handle of a 2006 Hummer H3, you will need a 10mm socket and a flathead screwdriver.

First, open the door and locate the round black cover near the door handle. This cover is about the size of half a dollar and is made of rubber or plastic. Using the flathead screwdriver, carefully pry off this cover.

Once the cover is removed, you will be able to see the bolt. Insert the 10mm socket and carefully remove the bolt, being careful not to let it fall inside the door panel.

After the bolt is removed, pull slightly on the door handle as if you were opening the door. This will allow the end cap of the door handle to move freely away from the door.

It is important to note that during this process, you should be cautious to avoid breaking any small tabs on the hinge end of the handle, as this may affect the integrity of the handle. Additionally, the "trigger" that unlatches the door may spring upward during removal, so be prepared to adjust it as needed.

Removing the handle assembly

To remove the handle assembly of a 2006 Hummer H3, you will need a deep well 10mm socket (or a standard 10mm socket with an extension) and a flathead screwdriver.

Firstly, open the door and locate the round black cover near the door handle. This cover is about the size of half a dollar and is made of rubber or plastic. Using the flathead screwdriver, carefully pry off this cover. Once the cover is off, you will see a bolt. Using the 10mm socket, carefully remove this bolt, being careful not to let it fall inside the door panel.

After the bolt is removed, pull slightly on the door handle as if you were opening the door. This will allow the end cap of the door handle to move freely away. Now, to remove the remaining handle assembly, pull slightly on the handle (again, as if to open the door) and, with the base of your other palm, hit the hinge end of the handle (the opposite end to the end cap) toward the rear of the vehicle while continuing to tug slightly. This action will release two small plastic nubs that hold the handle in place, and the remaining handle assembly will come free. You may need to hit it a few times.

Reinstalling the new handle

To reinstall the new door handle, you will need a deep well 10mm socket or a standard 10mm socket with an extension, and a flathead screwdriver.

First, you will need to attach the bolt to the new handle. This is the reverse of the first step in the removal process. Ensure that the bolt is securely attached, being careful not to let it fall inside the door panel.

Next, slot the new handle into place, ensuring that the trigger is in the correct position. You may need to use a bread tie to hold the trigger down while you do this.

Once the handle is in place, you can reattach the round black cover that you removed at the beginning of the process. This should be secured with the same bolt that you removed earlier.

Finally, test the handle to ensure that it is working correctly. The whole process should take around 30 minutes for all five handles.

Frequently asked questions